Repair for dryers that will not start, heat, tumble, shut off early, make noise or take too long to dry, in gas and electric models.
The dryer is one of the hardest-working appliances in Nashville homes, and when it takes two cycles to dry a load, it is also one of the most expensive to run. Dryers fail in familiar ways: no heat, no tumbling, a loud thump or squeal, a door that pops open or a cycle that ends damp. They are also a common source of house fires when lint and vents are neglected, so repair and venting go hand in hand.
We test the belt, drum rollers and glides, idler pulley, motor, thermal fuse, thermostats, heating element or gas igniter, door switch, moisture sensor and control. We also check the vent for lint buildup, because a blocked vent causes many of these problems and is a fire hazard. After the repair we run the dryer through a full heated cycle and confirm that air flows freely at the exterior vent.
A snapped belt, a worn idler pulley or a failed motor leaves the drum still.
A blown thermal fuse, a failed element or igniter or a bad thermostat is the usual reason.
Drum rollers, glides and bearings squeal, thump or rumble, and we replace the worn parts.
A blocked vent, a failing element or a sensor problem makes loads take far too long.
Drag the handle to compare.
BeforeAfterTumble restored.
Elements, igniters and fuses.
Airflow checked every time.
Lint and fire risk addressed.
Right fit.
Verified before we leave.
Every topic has its own page with what to expect and how we approach it.
Topic guideError Codes and Warning SignsWhat common error codes, noises, smells and symptoms mean and when to stop using an appliance and call…Learn more 
Topic guideAppliance Lifespan GuideTypical lifespans for refrigerators, ranges, washers, dryers, dishwashers and water heaters, and the habits that stretch them.Learn more 
Top appliance brandSpeed QueenA laundry specialist known for commercial-grade washers and dryers, now also sold for home use and found in…Learn more Enter the appliance, its age, the repair quote and a new unit price to see a plain repair or replace recommendation.
You tell us the brand, the model and what the appliance is doing, and we give you early guidance and set a visit that fits your day.
A technician inspects the appliance, reads codes and tests parts with meters and gauges to find the real cause.
You get a plain written plan with the parts, the work and the cost, and honest advice on repair or replace.
We repair with parts matched to your model, or install the new appliance level, connected and secured.
We run the appliance through a full cycle, check for leaks and show you how it works before we leave.
We keep a record, answer questions and stay available if anything seems off after the visit.
A clogged vent, a failing element or igniter or a sensor problem is typical, and the vent is the first thing to check.
Worn drum rollers, a glide or an idler pulley are the usual causes.
A thermal fuse, element, igniter or thermostat has probably failed.
Yes. Lint is flammable, so keep the vent clear and have it cleaned regularly.
Yes, and each has its own page with more detail.
Gas Dryer RepairCareful repair for gas dryers: igniters, flame sensors, gas valves, burners and venting, with safety checks on every…Explore 
Electric Dryer RepairRepair for electric dryers: heating elements, thermal fuses, thermostats, belts, motors, cords and 240 volt connection problems.Explore 
Dryer Not Heating RepairFast diagnosis and repair when a dryer runs but does not heat, heats weakly or takes several cycles…Explore 
Dryer Vent CleaningFull-length dryer vent cleaning that removes lint from the duct and exterior hood, restores airflow and reduces fire…Explore Tell us about your appliance and we will call you back to set up a visit.
Or call (615) 357-7797 to talk now.
